Elliott’s Rapid Hawk Assisted Tube Rolling System utilizes an electronic torque control system to precisely measure tube expansion and consistently hit target every time. For the first time, an electronic torque control can be used regardless of the motor’s power source.

• Tube Size: 0.500" to 3.00" (12.7 - 76.2mm) OD

• Torque Control

• Consistent Tube Expansion

• Operator Friendly

• Large Radial Reach

Elliott’s Tube Hole Gauges make it easy to accurately measure tube IDs and tube sheet holes found in vessels such as heat exchangers, chillers, and surface condensers.

• Tube Size: 0.375” to 2.000” (9.5 – 51.0mm) OD

Engineered to productively and precisely expand small tubes commonly found in oil coolers and other small heat exchangers. Elliott’s tabletop assisted tube rolling system completes the job right the first time.

• Tube Size: 0.25" to 0.625" (6.35 - 15.875mm) OD

• Direct Torque™ Electric Torque Control

• Increased Productivity

• Operator Friendly

• Consistent Tube Expansion

Elliott’s One-Revolution Series tube cutters are unlike any other one-revolution cutter. Using more advanced engineering principles the cutter and blade have been designed to last longer, withstand more wear, and require less force to cut the tube.

• Tube Size: 0.375" to 2.500" (9.53 - 63.5mm) OD

• Reach: 6" & 12" (152.4 & 304.8mm)

• Type: Tube Cutter

• Great For Puncturing Or Cutting

Elliott’s GT Series Grooving Tools, also known as Serrating Tools, can be used manually to clean up existing grooves or can be used in milling or drilling equipment for OEM tube sheet thicknesses of 3/8” (9.5mm) through 2-1/8” (54.0mm).

• Tube Size: 0.375" to 3.000" (9.5 - 76.2mm) OD

Elliott’s ETF Series Tube End Facers are ideal for trimming heat exchanger, condenser, and chiller tubes to a specific tube projection after tube expansion.

• Tube Size: 0.375" to 1.500" (9.5 - 38.1mm) OD

Elliott’s Tube Pilots, also known as Tube Guides, are used to pilot replacement tubes through tube sheets and tube support plates that are commonly found in heat exchangers and surface condensers.

• Tube Size: 0.500” to 1.500” (12.7 – 38.1mm) OD

Elliott’s hydraulic pumps are used to power the Collet Style Tube Tugger, Cyclegrip Semi-Continuous Puller, Tube Tuggers, and Stub Tugger. The hydraulic pumps’ compact design is ideal for use in confined work areas.

• Maximum Pressure: 5,000 or 10,000 PSI

• Power Source: Electric 110V or 220V, Pneumatic, or Manual

Elliott’s Tube Sheet Hole Brushes clean and remove hard deposits from tube sheets and support plate holes in surface condensers and heat exchangers.

• Tube Size: 0.250” to 1.250” (6.4 – 31.8mm) OD

Elliott’s ELC110220 is the first torque control with an Embedded Logic Controller that senses and is compatible with both 110V or 220V automatic, and manual reverse rolling motors.

• Tube Size: 0.250" to 3.000" (6.4 - 76.2mm) OD

• Voltage: 110V to 240V

• Languages: English or Spanish

• Compatibility: Elliott’s 99 Series Electric Rolling Motors (other electric motors with optional adapters)

• Auto-Reverse

Elliott’s Stub Tugger is a powerful hydraulic tube pulling system for removing tubes from both heat exchangers and boilers.

• Tube Size: 0.375” to 3.000” (9.5 – 76.2mm) OD

• Type: Stub Puller

• Application: Heat exchangers and boilers

• Pulling Capacity: 30 Ton (27.2Mt)

• Stroke: 6" (152.4mm)

Elliott’s 24 Series Condenser Expanders are ideal for expanding tubes in chillers, heat exchangers, feedwater heaters, fin fan coolers, and surface condensers.

• Tube Size: 0.500" to 2.000" (12.7 - 50.8mm) OD

• Roll Type: Straight

• Application: Chiller, heat exchanger, feedwater heater, fin fan cooler, and surface condenser.

Elliott's PX24 Series offer true parallel pin tube expansion, which can reduce the stress created on welded tube joints when compared to tapered rolling.

• Tube Size: 0.750″ to 1.000″ (19.05 – 25.4mm) OD

• Roll Type: Parallel Pin Condenser Expander

• Application: Chillers, heat exchangers, feedwater heaters, fin fan coolers, and surface condensers.

Elliott’s 900 Series Flaring Boiler Expanders are self-feeding, specifically made for use in superheaters in watertube boilers or evaporator tubes. In only one operation, these expanders roll tubes parallel and flare projecting tube ends at 15 degrees from the tool center line.

• Tube Size: 0.620” to 1.500” (15.4 – 38.1mm) OD

• Roll Type: Flaring

• Application: Superheaters, watertube boilers, and evaporator tubes.

• Tube Size: 0.250" to 0.375" (6.4 - 9.5mm) OD

• Roll Type: Straight

• Application: Chiller, heat exchanger, feedwater heater, fin fan cooler, and surface condenser.

Elliott’s 4480 Series Single Roll Beading Expanders expand the tube into the tube sheet while forming a bead at the end of the tube required in Firetube boiler applications.

• Tube Size: 1.500” to 3.000” (38.1 – 76.2mm) OD

• Roll Type: Roll Beading

• Application: Firetube Boiler

Elliott’s collet style tube puller is designed to quickly pull tube stubs from tube sheets without damaging the tube sheet hole. Offering the gripping power of a spear with the speed and convenience of a collet.

• Tube Size: 0.50″ to 2.50″ (12.7 – 63.5mm)

• Type: Tube Puller

• Application: Condensers, chillers, heat exchangers, boiler air heaters, and paper mill evaporators

• Pulling Capacity: Up to 25 Tons

• Pulling Stroke: 6.00″ (152.4mm)

Elliott’s Manual Tube Puller is ideal for pulling a limited number of tubes in heat exchangers, chillers, fin fan coolers, and surface condensers.

• Tube Size: 3/8” to 1.000” (9.5 – 25.4mm) OD

• Type: Tube Puller

• Application: Heat exchangers, chillers, fin fan coolers, and surface condensers

Elliott’s PTTC (Push Type Tube Cutter) Series Cutters accommodate heat exchangers and boilers. The adjustable collar allows tubes to be cut or scored just beyond the tube sheet. The cutting blades are specially coated to increase longevity.

• Tube Size: 0.375” to 2.500” (9.5 – 63.5mm) OD

• Type: Tube Cutter

• Tube Sheet Thickness: 5" - 12" (127.0 - 304.8mm)

• Non-Ferrous/Steel or Stainless Steel Cutter Blades

Elliott’s 300 Series Boiler Tube cutters are power driven to cut tubes to length in Firetube and Watertube boilers prior to roll beading.

• Tube Size: 2.000" to 3.000" (50.8 - 76.2mm) OD

• Type: Tube Cutter

• Male Square Drive: 1" (25.4mm)

• Drive Source: Motors with ≤ 150 RPM or Ratchet

Elliott’s 40 Series Straight Boiler Expanders are recommended for re-rolling leaky tube joints in Firetube boilers. Self-feeding, these expanders should primarily be used by hand.

• Tube Size: 2.000” to 3.000” (50.8 – 76.2mm) OD

• Roll Type: Straight

• Application: Firetube Boiler

Elliott’s Collet Style Tube Tugger was designed for fast and efficient tube removal in condensers, chiller, and other heat exchangers. With its 6 Ton pulling capacity, the Collet Style Tube Tugger automatically grips, pulls, and releases the tube in a matter of seconds.

• Tube Size: 0.625” to 1.000” (15.9 – 25.47mm) OD

• Type: Tube Puller

• Application: Condensers, chillers, or heat exchangers

• Pulling Capacity: 6 Ton

• Stroke: 3" (76.0mm)

• Pulling Stroke: 2.25" (57.2mm)

Elliott’s Cyclgrip Semi-Continuous Tube Puller is an engineered product that continuously pulls chiller, heat exchanger, and condenser tubes after the tubes have been pulled free from the tube sheet, making it the ideal companion for the Collet Style Tube Tugger.

• Tube Size: 0.500” to 1.000” (12.7 – 25.4mm) OD

• Type: Tube Puller

• Pulling Speed Per Minute: 10' (3.3m)

Elliott’s Tube Tugger is a powerful continuous hydraulic tube pulling system for removing any type of tube material effortlessly from heat exchangers, chillers, and other heat transfer vessels.

• Tube Size: 0.625” to 1.250” (15.9 – 31.8mm) OD

• Type: Tube Puller

• Application: Heat exchangers, chillers, and other heat transfer vessels

• Pulling Capacity: 30 Ton (27Mt)

• Stroke: 3" (76.2mm)

Elliott’s Super Tube Tugger is a powerful continuous hydraulic tube pulling system for removing any type of tube material effortlessly from boilers and surface condensers.

• Tube Size: 1.500” to 2.000” (38.1 – 50.8mm) OD

• Type: Tube Puller

• Application: Boilers and Surface Condensers

• Pulling Capacity: 60 Ton

• Stroke: 4" (101mm)

Elliott’s TT Spears are used with the Elliott Tube Tugger or Super Tube Tugger to successfully pull tubes in chillers, heat exchangers, condensers, fin fan coolers, and boilers.

• Tube Size: 0.625” to 2.000” (15.9 – 50.8mm) OD

• Type: Tube Spear

Elliott’s DRE Series Deep Roll Boiler Expanders are used for deep and hard rolling of steam and mud drums found in high-pressure boilers.

• Tube Size: 1.750” to 4.000” (44.5 – 101.6mm) OD

• Roll Type: Straight

• Application: Steam & Mud Drums and Watertube Boiler

Elliott’s 6621 Series Sugar Mill Vacuum Pan Expanders are ideal for the fabrication and re-tube of sugar mill vacuum pans.

• Tube Size: 3.000” to 4.000” (76.2 – 101.60mm) OD

• Roll Type: Straight

• Application: Sugar Mill

Elliott’s E Series Hex Spears are used with the Elliott Stub Tugger or Manual Tube puller to successfully pull tubes in chillers, heat exchangers, condensers, fin fan coolers, and boilers.

• Tube Size: 0.375" to 3.000" (9.5 - 76.2mm) OD

• Type: Tube Spear

Elliott’s Jumbo Tube Buster is the recommended driving tool for Elliott’s Jumbo Knockout Tools to remove tube stubs in heat exchangers, Firetube boilers, and Watertube boilers.

• Tube Size: 0.625” to 2.000” (15.9 – 50.8mm) OD

• Type: Tube Buster

Elliott’s 3300 Series Straight Boiler Expanders are the preferred tube expanders for expanding tubes in Firetube boilers or in self-contained steam boiler units. They are recommended for any requirement for parallel expansion of tubes in tube sheets.

• Tube Size: 1.500” to 4.000” (38.1 – 101.6mm) OD

• Roll Type: Straight

• Application: Firetube Boiler and Steam Boiler

Elliott’s 3400 Series Flaring Boiler Expanders are the recommended tube expanders for expanding and flaring tubes in Firetube and watertube boilers. The prong style collar allows for uniform flare lengths as well as torque controlled tube rolling to obtain uniform expanded joints.

• Tube Size: 1.500” to 4.000” (38.1 – 101.6mm) OD

• Roll Type: Flaring

• Application: Firetube and Watertube Boiler

Elliott’s 1500 Series Flaring Boiler Expanders are self-feeding, specifically made for use in Firetube and watertube boilers. In only one operation, these expanders roll tubes parallel and flare projecting tube ends at 20 degrees from the tool center line.

• Tube Size: 1.750” to 4.000” (44.5 – 101.6mm) OD

• Roll Type: Flaring

• Application: Firetube Boiler and Watertube Boiler

The powerful ET75 Series Nutrunners are ideal for use in tough industrial applications and for opening and closing valves in industrial plants. The right angle heads are suited for use in hard to reach, tight areas.

• Torque Range: 70 - 325 ft lbs (75 to 440 Nm)

• Type: Stall Type Angle Nutrunners

The first rolling system of its kind, offering the speed and productivity of a patent pending electric servo motor with the capability to perform parallel pin and traditional expansion.

• Tube Size: 0.625″ to 1.500″ (15.9 – 38.1mm) OD

• Parallel and Traditional Pin Tube Rolling

• Up To 2X The Speed Of Conventional Rolling

• Automatic Tool Lubrication

• Large Radial Reach

• Easy To Move

• Operator Friendly Controls

• Tube Size: 3/4″ to 1″ (19.1 – 25.4mm) OD

• Tube Section: Straight

• Deposit Type: Soft, Gummy, or Organic

• Thickness: Light to Medium

• Flush: Wet

The Jumbo Jiffy Gun is powered by an air and water combination to propel reusable shoot through devices. Elliott’s Jumbo Jiffy Gun is the preferred method for cleaning condenser tubes in power utility plants, pulp, paper, steel mills, and petrochemical plants.

• Tube Size: 3/8″ to 1-1/4″ (9.5 – 31.8mm) OD

• Tube Section: Straight

• Deposit Type: Soft, Gummy, or Organic

• Thickness: Light & Medium

• Flush: Wet

Elliott’s Mechanical Tube Plugs create a positive mechanical contact seal in excess of 6,500 PSI (448.2 bar), making them ideal for high-pressure applications.

• Tube Size: 0.410” to 1.000 (10.4 to 25.4mm) ID

• Maximum Pressure: 6,500 PSI

• Materials: Brass, Steel, Stainless, Titanium, and more.

• ASME PCC-2-2015 Compliant

• Comprehensive Testing and Quality Assurance Standards.

• Easy To Install- No Hydraulic Equipment Needed.

Elliott’s One-Piece Tube Plugs cover a wide tube OD range, making them ideal for sealing leaky tubes in both heat exchangers and boilers.

• Tube Size: 0.375" to 3.000" (9.5 - 76.2mm) OD

• Maximum Pressure: 150 PSI

• Materials: Brass, Carbon Steel, Stainless Steel, Aluminum, Monel, and more.

Elliott’s Two-Piece Tube Plugs offer more sealing due to the tapered pin design. This gives even expansion to the ring and a long contact to the seal.

• Tube Size: 0.375” to 1.250 (9.5 - 31.8mm) OD

• Maximum Pressure: 150 PSI

• Materials: Brass, Carbon Steel, Stainless Steel, Aluminum, and more.

The powerful 445 Series Motors are ideal for tough boiler tube applications. The right angle heads are suitable for rolling tubes in hard to reach, tight areas. Now available in torque controlled & stall type motors.

• Tube Size: 1.500” to 4.000” (38.1 – 101.6mm) OD

• Type: Right Angle Pneumatic Rolling Motor

• Style: Torque Controlled or Stall Type

Elliott’s 99 Series electric rolling motors offer better consistency, faster RPMs, and comparable torque to that of pneumatic offerings.

• Tube Size: 0.250” to 3.000” (6.4 – 76.2mm) OD

• Type: Rolling Motor

• Power: Electric 110V or 220V

• Torque: Torque Controlled with ELC

The Midi/Maxi Series Pneumatic Rolling Motors are manufactured with quality materials to provide motor robustness and durability for years to come.

• Tube Size: 0.750” to 2.000” (19.1 – 50.8mm) OD

• Type: Rolling Motor

• Power: Pneumatic

• Torque: Torque Controlled

Elliott’s Stall Torque Pneumatic Rolling Motors are the most powerful motors available for rolling tubes in extreme applications. The motors are recommended for use in heavy wall, thick drum applications in watertube boilers.

• Tube Size: 0.750” to 6.000” (19.1 – 152.4mm) OD

• Type: Rolling Motor

• Power: Pneumatic

• Torque: Stall Torque

Elliott’s Heat Exchanger Tube Cleaners utilize a rigid shaft to provide high torque cleaning to remove hard deposits often found in heat exchanger tubes. These cleaners are ideal in sugar mills, paper mills, chemical plants, and oil refineries.

• Tube Size: 1/2″ to 2.0″ (9.5 – 50.8mm) OD

• Tube Section: Straight

• Deposit Type: Soft, Gummy, Organic, Hard Powder, & Rock Solid

• Thickness: Light, Medium, Heavy

• Flush: Wet & Dry

The Jiffy Gun is powered by an air and water combination to propel reusable shoot through devices. Elliott’s Jiffy Gun is the preferred method for cleaning condenser tubes in power utility plants, pulp, paper, steel mills, and petrochemical plants.

• Tube Size: 3/8″ to 3/4″ (9.5 – 19.0mm) OD

• Tube Section: Straight

• Deposit Type: Soft, Gummy, or Organic

• Thickness: Light & Medium

• Flush: Wet

The RECON 1250 and 2500 are simple to operate. Connect the air supply, insert the seals into both sides of the tube ends and pressurize the tubes. Then monitor the gauges for drops in air pressure, which indicate a tube leak.

• Tube Size: 0.500” to 2.500 (12.7 – 63.5mm) OD

• Type: Pressure Test Gun

The air turbine style motor design provides an immediate and powerful startup to drive the cleaning head down the tube at a high speed, removing light to medium deposits of scale, mud, and other process residues.

• Tube Size: 0.495″ to 13.225″ (12.57 – 335.9mm) OD

• Tube Section: Straight & Curved

• Deposit Type: Soft, Gummy, Organic, Hard Powder, & Rock Solid

• Thickness: Light to Heavy

• Flush: Dry

Operating the RECON 1500 Tube Leak Test Gun is simple. With the air supply connected, plug one tube end with the test gun and the other end with the T-Handle Plugging Tool. Press the lever trigger and the Venturi System quickly and efficiently evacuates the tube. Then monitor the gauge for loss of vacuum, which indicates a tube leak.

• Tube Size: 0.280” to 2.456” (7.1 – 62.4mm) ID

• Type: Vacuum Test Gun

Elliott’s Die-Hard™ is the first cableless tube cleaner that successfully cleans light to medium deposits found in chiller, condenser, and heat exchanger tubes.

• Tube Size: 3/4″ to 1″ (19.1 – 25.4mm) OD

• Tube Section: Straight

• Deposit Type: Soft, Gummy, or Organic

• Thickness: Light to Medium

• Flush: Wet

Elliott's Pneumatic Hammer is the recommended tool for removing tube stubs in heat exchangers or beading tubes in firetube boilers.

• Tube Size: 0.250" to 3.000" (6.4 - 50.8mm) OD

Elliott’s Roto-Jet Tube Cleaning Systems are an effective solution to increasing chiller, condenser, and other heat exchanger efficiency.

• Tube Size: 0.312″ to 2.0″ (7.9 - 50.8mm) ID

• Tube Section: Straight or Curved

• Type: Soft, Gummy, Or Organic

• Thickness: Light to Medium

• Flush: Wet & Dry

Elliott’s Lubricants are engineered to provide the best lubrication in tube rolling and roll beading applications. They will provide time and tool savings compared to commonly available lubricants.

• Paste Lubricant

• Liquid Lubricant

• Bead Coolant

• Cutting Oil

The Soot Buster, used for cleaning firetube boiler tubes, is a pneumatically actuated cleaning tool that propels itself inside of tubes and scrubs the tube ID with each pulse.

• Tube Size: 1-1/4″ to 4″ (31.8 – 101.6mm) OD

• Tube Section: Straight

• Deposit Type: Soft (Soot)

• Thickness: Light & Medium

• Flush: Dry

Elliott’s Collet Style Support Sheet Expanders are used with a handheld short stroke hydraulic ram and lightweight, low-pressure hydraulic pump to support sheet expand finned or prime surface tubes commonly found in chillers.

• Tube Size: 0.750” to 1.000” (19.1 – 25.4mm) OD

• Roll Type: Straight

• Application: Chiller

Elliott’s 3321 Series Sugar Mill Vacuum Pan Expanders are ideal for re-rolling tubes in vacuum pans.

• Tube Size: 3.000” to 4.000” (76.2 – 101.6mm) OD

• Roll Type: Straight

• Application: Sugar Mill